linux ntp Archives - Page 9 of 10

Choosing a NTP Server and Selecting the Best Timing Source for You

September 10, 2008 | By Richard N Williams

The NTP server is an integral part of the modern computer network. Without Network Time Protocol and NTP time servers many of the modern functionality of computers that we take for granted such as online reservation, Internet trading and satellite communication would be impossible.

Synchronisation in computers is dealt with by NTP. NTP and NTP servers use a single time reference to synchronise all machines on a network to that time. This time reference could in fact be anything such as the time on a wrist watch perhaps. However, synchronisation is pointless unless a UTC (coordinated universal time) time source is used as UTC has been developed to allow the whole world to synchronise to the same time, allowing truly global synchronisation.

UTC is based on the time told by atomic clocks although compensation measures such as Leap Seconds are added to UTC to keep it inline with Greenwich Meantime (GMT).

Atomic clocks are very expensive and extremely delicate pieces of equipment and not the sort of thing that can be housed in the office server room. Fortunately a NTP server can receive a UTC time source from several different locations.

The Internet is perhaps the most widely used source of time references. Unfortunately however, there are draw backs in using the Internet for a timing source. Firstly the Internet timing sources can’t be authenticated. Authentication is a security measure used by NTP to check that timing source is genuine. Secondly, to use an Internet timing reference means a hole has to be left open in the network’s firewall, again compromising security. Thirdly, Internet timing sources are notoriously inaccurate and those that aren’t can often be too far away from a client to provide any useful precision.

However, if security and high level of accuracy to UTC time is not required then the Internet can provide a simple and affordable solution.

A far more secure method of receiving a UTC timing reference is to use the specialist national time and frequency transmission broadcast by several countries. The UK (MSF), USA (WWVB), Germany (DCF) and Japan (JJY) all boast a long wave timing signal. While these signals are limited in range and strength, where available they make an ideal timing source as the radio receiver can pick these signals up from inside a building. These transmissions can also be authenticated providing a high level of security.

The third and perhaps simplest solution is to use a GPS NTP server. These use the signals sent from the Global Positioning System which contains timing information. This is ideal as the GPS signal can be received literally anywhere in the world so if there is no radio transmission your area then the GPS network will provide a secure and authenticated solution.

The only downside to GPS is that an antenna has to have a good view of the sky and therefore need to be positioned on the roof. This obviously has logistical drawbacks if the server room is in the basement of a sky-scraper.

In selecting a timing source, the most important thing to remember is where the NTP server is going to be situated. If it is indoors and there is no opportunity to run and antenna to the roof then the radio transmissions would be the best alternative. If there are no radio transmission in your country/area or the signals are blocked by local topography then the GPS is an ideal solution.

However, if accuracy and security are not an issue then the Internet would be the most obvious solution.

Understanding a NTP GPS Server

September 8, 2008 | By Richard N Williams

A NTP GPS Server is a type of time server that uses Network Time Protocol (NTP) as a method for synchronizing the time on network devices and computers after receiving a time signal from he GPS network.

The GPS (Global Positioning System) network is a constellation of satellites owned and operated by the USA military. Most people are aware of GPS as an aid for satellite navigation. In actual fact, the basis of the transmissions broadcast by the GPS satellites is a time signal. This time signal is generated by the satellite’s onboard atomic clock. It is this information that a satellite navigation system receives and calculates by triangulation the distance away from the satellites.

This timing signal is what is used by a NTP GPS server as a reference to synchronize a network too. NTP then distributes this time to all routers and computers on that network.

A NTP GPS server comprises of a GPS receiver, GPS antenna and NTP software. The GPS antenna should be situated on a rooftop which will give the best possibility of receiving the transmissions from the satellites.

The GPS receiver then converts this information into timing information that can be read and distributed by NTP.

While the atomic clocks onboard the GPS satellites do not transmit a UTC timing code (Coordinated Universal Time). However, NTP has the ability to convert the atomic clock from the satellites to UTC. This allows computer networks to be synchronized to the same universal time source no matter where they are in the world.

Using a dedicated NTP GPS server a network can be synchronized to within a few milliseconds of UTC time with accuracies of a few hundred nanoseconds made possible over LAN’s.

Time Servers: Maintaining Precise Time on Your Computers

September 8, 2008 | By Richard N Williams

Computer networks rely on timekeeping for nearly all their applications, from sending an email to saving data, a timestamp is necessary for computer to keep track. All routers and switches need to run at the same rate, out of sync devices can lead to data being lost and even entire connections.

All PC’s and networking devices use clocks to maintain an internal system time. These clocks, called Real Time Clock chips (RTC) provide time and date information. The chips are battery backed so that even during power outages, they can maintain time.

However, personal computers are not designed to be perfect clocks, their design has been optimized for mass production and low-cost rather than maintaining accurate time. However, these internal clocks are prone to drift and although for many application this can be quite adequate, often machines need to work together on a network and if the computers drift at different rates the computers will become out of sync with each other and problems can arise particularly with time sensitive transactions.

For some transactions it is necessary for computers to be perfectly synchronised, even a few seconds difference between machines can have serious effects, such as finding an airline ticket you had booked had been sold moments later to another customer or you could draw your savings out of a cash machine and when your account is empty you could quickly going to another machine and withdraw it all again.

Time servers are like other computer servers in the sense they are usually located on a network. A time server gathers timing information, usually from an external hardware source and then synchronises the network to that time.

Most time servers use NTP (Network Time Protocol) which is one of the Internet’s oldest protocols still used, invented by Dr David Mills from the University of Delaware, it has been in utilized since 1985. NTP is a protocol designed to synchronize the clocks on computers and networks across the Internet or Local Area Networks (LANs).

NTP utilises an external timing reference and then synchronises all devices on the network to that time.

Often time servers are synchronised to a UTC (Coordinated Universal time) source which is the global standard time scale and allows computers all over the world to synchronised to exactly the same time. This has obvious importance in industries where exact timing is crucial such as the stock exchange or airline industry.

There are various sources that a time server can use as a timing reference. The Internet is an obvious source, however, internet timing references from the Internet such as nist.gov and windows.time can not be authenticated, leaving the time server and therefore the network vulnerable to security threats.

Understanding Computer Timestamps with NTP

September 8, 2008 | By Richard N Williams

The way a computer deals with time is totally different to the ways humans perceive it. We arrange time into seconds, minutes, hours, days, weeks, months and years, while computers on the other hand arrange time as a single number representing the seconds that have passed from a single point in time, known as the prime epoch.

Most computers use NTP (Network Time Protocol) to deal with time and on networks many are synchronised using a dedicated NTP time server. NTP knows nothing about days, years or centuries, only the seconds from the prime epoch. This prime epoch is set (for most systems) at midnight at the turn of the century twentieth century that for a human would be recorded as something like: 00:00 – 01,01,1900.

Computers, however, count time as the number of seconds past this point. If a computer was around in 1900 its timestamp on midnight January 1 would be 0 while in 1972 at the same date the timestamp would be 2,272,060,800, which represents the number of seconds since 1900.

The timestamps restart every 136 years with the next wrap around due in 2036, this has caused uneasiness amongst some who fear a Millennium Bug type scenario, although most doubt such events would occur, however, when a wrap-around of the timestamp does happen an era integer will be added (+1), to allow computers to deal with time spans that cover more than one wrap-around. If computers and NTP need to deal with time that spans before the prime epoch a negative integer is used (for the year 1500 a -3 will be used to represent three cycles of 136 years).

Timestamps are used in virtually every transaction that modern computers are tasked to do such as sending emails, debugging and programming. Because time is linear, a computer knows that each timestamp is always greater than the previous one and therefore computers and NTP find it difficult to deal with inaccuracies in time, particularly when time suddenly appears to go backwards.

This can happen if computers are not synchronised to the same time. If an email is sent to a machine with a slower clock, it appears to the computer to have been received before it has been sent. Lack of synchronisation can serious problems and can even leave a system vulnerable to malicious attacks and even fraud.

Because of this, most computer networks are synchronised to UTC (Coordinated Universal Time). UTC is a global timescale and the same for everybody worldwide it is based on the time told by atomic clocks which are highly accurate, neither gaining nor losing a second in millions of years.

Most computer networks use a dedicated NTP time server to receive a UTC time to synchronise their computers too. UTC is available from across the Internet (although unsecured), via the GPS network (Global Positioning System), or by receiving national time and frequency broadcasts via long wave.

NTP synchronises a computer by checking the received UTC time and adding to or holding a computer’s timestamp until it perfectly matches UTC. By using a dedicated NTP time server UTC can be maintained on a network to a few milliseconds of UTC time.

A Beginners Guide To The NTP Server

September 8, 2008 | By Richard N Williams

Computer networking is one of the most difficult aspects of information and communications technology (ICT). The logistics of connecting terminals, routers, printers and all the other devices can leave many administrators with a constant headache.

One of the most important aspects that often gets overlooked and can have disastrous consequences is that of time synchronization.

It is imperative that all devices on a network are telling the same time as timestamps, the format a computer relays time to each other, are the only form of reference a computer can use to establish a sequence of events. If different machines on a network are telling different times then unforeseen consequences such as emails arriving before they have technically been sent and other anomalies will make the administrator’s headache even worse.

What’s more a computer network that is not synchronized is open to security threats and even fraud. Fortunately the NTP time server has been around for many years and can ease the headache of time synchronization .

NTP (Network Time Protocol) is one of the oldest protocols used by computer networks. Developed nearly three decades ago NTP is a protocol that checks the time on all devices on network and adds or subtracts enough time to ensure they are all synchronized.

NTP requires a time reference to synchronise the network’s clocks to. Whilst NTP can synchronize a network to any time an authoritative time source is obviously the best solution. UTC (Coordinated Universal Time) is a globally used timescale based on the time told by atomic clocks. As atomic clocks lose less than a second of time in over a thousand years, UTC is by far the best timing source to synchronize a network to. Not only will your network be perfectly synchronized together but also your network will be synchronized to the same time as millions of computer networks all from around the world.

A NTP server can receive a UTC time reference from several sources. The Internet is the most obvious source, however Internet timing sources are notoriously inaccurate and those that are not can be relatively useless if the distance is too far away. Also having placed your NTP server securely behind your firewall it does seem pointless to have to keep a hole open in it to allow the NTP server to poll the timing reference from across the web and leave the entire network vulnerable, particularly as NTP authentication (NTP’s own security measure) is not possible over the Internet.

There are two far more secure and accurate methods of receiving a UTC timing reference. The first is to utilise the national time and frequency transmissions that several countries broadcast from their national physics laboratories. These are usually broadcast via long wave which has an advantage of being able to be picked up inside a server room although many countries do not have such a signal.

However, many NTP servers can utilize the timing signal broadcast by the onboard atomic clocks of the GPS (Global Positioning System) satellites. This signal is available everywhere but a GPS antenna is required that can get a clear view of the sky.

By utilizing a UTC timing source either through the GPS network of radio transmission a computer network can be synchronized to within a few milliseconds of UTC time.

NTP GPS Server for Time Critical Applications

September 8, 2008 | By Richard N Williams

The GPS (Global Positioning System) is a Global Navigational Satellite System (GNSS) controlled and run by the United States of America.

GNSS systems work by using satellites several thousand miles above the Earth’s surface that beam timing information down to a GNSS receiver (like the satellite navigation unit in our cars). It is this information that is used by the GPS receiver to triangulate an exact position. They can only do this by having onboard their own highly accurate atomic clock as the distance the satellites are away from the Earth, even an inaccuracy of a second or two could mean a sat navigation’s location could be miles out.

As a consequence of having this accurate time sources, GPS and the new breed of GNSS systems can all be used to receive an absolute or UTC (Universal Coordinated Time) time source. This time source can be used by computer networks running a NTP server (Network Time Protocol) to synchronise all machines and devices to the same time.

NTP is a protocol designed to synchronise computers and network devices to an external timing reference.

GPS is an ideal time and frequency reference because it can provide highly accurate time anywhere in the world using relatively cheap components. Each GPS satellite transmits in two frequencies L2 for the military use and L1 for use by civilians transmitted at 1575 MHz, Low-cost GPS antennas and receivers are now widely available and dedicated NTP GPS servers are now relatively low cost.

The radio signal transmitted by the satellite can pass through windows but can be blocked by buildings so the ideal location for a GPS antenna is on a rooftop with a good view of the sky. The more satellites it can receive from the better the signal. However, roof-mounted antennas can be prone to lighting strikes or other voltage surges so a suppressor is highly recommend being installed inline on the GPS cable.

A NTP GPS Server is ideal in providing NTP time servers or stand-alone computers with a highly accurate external reference for synchronisation. Even with relatively low cost equipment, accuracy of hundred nanoseconds (a nanosecond = a billionth of a second) can be reasonably achieved using GPS as an external reference.