UTC What Time is it?

  |   By

From the early days of the industrial revolution, when railway lines and the telegraph spanned across time zones it became apparent that a global timescale was required that would allow the same time to be used no matter where you were in the world.

The first attempt at a global timescale was GMT – Greenwich Meantime. This was based on the Greenwich Meridian where the sun is directly above at 12 noon. GMT was chosen, primarily because of the influence of the British empire on the rest if the globe.

Other timescales had been developed such British Railway Time but GMT was the first time a truly global system of time was used throughout the world.

GMT remained as the global timescale through the first half of the twentieth century although people began referring to as UT (Universal Time).

However, when atomic clocks were developed in the middle of the twentieth century it soon became apparent that GMT was not accurate enough. A global timescale based on the time told by atomic clocks was desired to represent these new accurate chronometers.

International Atomic Time (TAI) was developed for this purpose but problems in using atomic clocks soon became apparent.

It was thought that the Earth’s revolution on its axis was an exact 24 hours. But thanks to atomic clocks it was discovered the Earth’s spin varies and since the 1970’s has been slowing. This slowing of the Earth’s rotation needed to be accounted for otherwise the discrepancies could build up and night would slowly drift in to day (albeit in many millennia).

Coordinated Universal Time was developed to counter this. Based on both TAI and GMT, UTC allows for the slowing of the Earth’s rotation by adding leap seconds every year or two (and sometimes twice a year).

UTC is now a truly global timescale and is adopted by nations and technologies across the globe. Computer networks are synchronised to UTC via network time servers and they use the protocol NTP to ensure accuracy.

Radio Controlled Clocks Atomic Clocks on Shortwave

  |   By

Atomic clocks are a marvel compared to other forms of timekeepers. It would take over 100,000 years for an atomic clock to lose a second in time which is staggering especially when you compare it to digital and mechanical clocks that can drift that much in a day.

But atomic clocks are not practical pieces of equipment to have around the office or home. They are bulky, expensive and require laboratory conditions to operate effectively. But making use of an atomic clock is straightforward enough especially as atomic time keepers like NIST (National Institute of Standards and Time) and NPL (National Physical Laboratory) broadcast the time as told by their atomic clocks on short wave radio.

NIST transmits its signal, known as WWVB from Boulder, Colorado and it is broadcast on an extremely low frequency (60,000 Hz). The radio waves from WWVB station can cover all of the continental United States plus much of Canada and Central America.

The NPL signal is broadcast in Cumbria in the UK and it is transmitted along similar frequencies. This signal, known as MSF is available throughout most of the UK and similar systems are available in other countries such as Germany, Japan and Switzerland.

Radio controlled atomic clocks receive these long wave signals and correct themselves according to any drift the clock detects. Computer networks also take advantage of these atomic clocks signals and use the protocol NTP (Network Time Protocol) and dedicated NTP time servers to synchronise hundreds and thousands of different computers.

NTP or SNTP That is the Question?

  |   By

While there are several protocols available for time synchronisation the majority of network time is synchronised using either NTP or SNTP.

Network Time Protocol (NTP) and Simple Network Time Protocol (SNTP) have been around since the inception of the Internet (and in the case of NTP, several years beforehand) and are by far the most popular and widespread time synchronisation protocols.

However, the difference between the two is slight and deciding which protocol is best for a ntp time server or a particular time synchronisation application can be troublesome.

As its name suggests, SNTP is a simplified version of Network Time Protocol but the question is often asked: ‘what exactly is the difference?’

The main difference between the two versions of the protocol is in the algorithm that is used. NTP’s algorithm can query multiple reference clocks an calculate which is the most accurate.

SNTP use for low processing devices – it is suited to less powerful machines, do not require the high level accuracy of NTP. NTP can also monitor any offset and jitter (small variations in waveform resulting from voltage supply fluctuations, mechanical vibrations or other sources) whilst SNTP does not.

Another major difference is in the way the two protocols adjust for any drift in network devices. NTP will speed up or slow down a system clock to match the time of the reference clock coming into the NTP server (slewing) while SNTP will simply step forward or backward the system clock.

This stepping of the system time can cause potential problems with time sensitive applications especially of the step is quite large.

NTP is used when accuracy is important and when time critical applications are reliant on the network. However, its complex algorithm is not suited to simple machines or those with less powerful processors. SNTP on the other hand is best suited for these simpler devices as it takes up less computer resources, however it is not suited for any device where accuracy is critical or where time critical applications are reliant on the network.

Atomic Clocks the Key to Network Synchronisation

  |   By

Sourcing the correct time for network synchronisation is only possible thanks to atomic clocks. Compared to standard timing devices and atomic clock is millions of times more accurate with the latest designs providing accurate time to within a second in a 100,000 years.

Atomic clocks use the unchanging resonance of atoms during different energy states to measure time providing an atomic tick that occurs nearly 9 billion times a second in the case of the caesium atom. In fact the resonance of caesium is now the official definition of a second having been adopted by the International System of Unit (SI).

Atomic clocks are the base clocks used for the international time, UTC (Coordinated Universal Time). And they also provide the basis for NTP servers to synchronise computer networks and time sensitive technologies such as those used by air traffic control and other high level time sensitive applications.

Finding an atomic clock source of UTC is a simple procedure. Particularly with the presence of online time sources such as those provided by Microsoft and the National Institute for Standards and Time (windows.time.com and nist.time.gov).

However, these NTP servers are what are known as stratum 2 devices that mean they are connected to another device which in turn gets the time from an atomic clock (in other words a second-hand source of UTC).

While the accuracy of these stratum 2 servers is unquestionable, it can be affected by the distance the client is from the time servers, they are also outside the firewall meaning that any communication with an online time server requires an open UDP (User Datagram Protocol) port to allow the communication.

This can cause vulnerabilities in the network and are not used for this reason in any system that requires complete security. A more secure (and reliable) method of receiving UTC is to use a dedicated NTP time server. These time synchronisation devices receive the time direct from atomic clocks either broadcast on long wave by places like NIST or NPL (National Physical Laboratory – UK). Alternatively UTC can be derived from the GPS signal broadcast by the constellation of satellites in the GPS network (Global Positioning System).

Atomic Clock to be attached to International Space Station

  |   By

One of the world’s most accurate atomic clocks is to be launched into orbit and attached to the International Space Station (ISS) thanks to an agreement signed by the French space agency.

The PHARAO (Projet d’Horloge Atomique par Refroidissement d’Atomes en Orbite) atomic clock is to attached to the ISS in an effort to more accurately test Einstein’s theory of relatively as well as increasing the accuracy of Coordinated Universal Time (UTC) amongst other geodesy experiments.

PHARAO is a next generation caesium atomic clock with an accuracy that corresponds to less than a second’s drift every 300,000 years. PHARAO is to be launched by the European Space Agency (ESA) in 2013.

Atomic clocks are the most accurate timekeeping devices available to mankind yet they are susceptible to changes in gravitational pull, as predicted by Einstein’s theory, as time itself is slewed by the Earth’s pull. By placing this accurate atomic clock into orbit the effect of Earth’s gravity is lessened allowing PHARAO to be more accurate than Earth based clock.

While atomic clocks are not new to orbit, as many satellites; including the GPS network (Global Positioning System) contain atomic clocks, however, PHARAO will be among the most accurate clocks ever launched into space, allowing it to be used for far more detailed analysis.

Atomic clocks have been around since the 1960’s but their increasing development has paved the way for more and more advanced technologies. Atomic clocks form the basis of many modern technologies from satellite navigation to allowing computer networks to communicate effectively across the globe.

Computer networks receive time signals from atomic clocks via NTP time servers (Network Time Protocol) which can accurately synchronise a computer network to within a few milliseconds of UTC.

Network Time Protocol For When Time Matters

  |   By

There is a certain irony that the computer that sits on your desktop and may have cost as much as month’s salary will have a clock onboard that is less accurate than a cheap wristwatch bought at a petrol or gas station.

The problem is not that computers are in particularly made with cheap timing components but that any serious timekeeping on a PC can be achieved without expensive or advanced oscillators.

The onboard timing oscillators on most PCs are in fact just a back up to keep the computer clock synchronised when the PC is off or when network timing information is unavailable.

Despite these inadequate onboard clocks, timing on a network of PC’s can be achieved to within millisecond accuracy and a network that is synchronised to the global timescale UTC (Coordinated Universal Time) shouldn’t drift at all.

The reason this high level of accuracy and synchronicity can be achieved without expensive oscillators is that computers can use Network Timing Protocol (NTP) to find and maintain the exact time.

NTP is an algorithm that distributes a single source of time; this can be generated by the onboard clock of a PC – although this would see every machine on the network drift as the clock itself drifts – A far better solution is to use NTP to distribute a stable, accurate source of time, and most preferably for networks that conduct business across the internet, a source of UTC.

The simplest method of receiving UTC – which is kept true by a constellation of atomic clocks around the globe – is to use a dedicated NTP time server. NTP servers use either GPS satellite signals (Global Positioning System) or long wave radio broadcasts (usually transmitted by national physics laboratories like NPL or NIST).

Once received the NTP server distributes the timing source across the network and constantly checks each machine for drift (In essence the networked machine contacts the server as a client and the information is exchanged via TCP/IP.

This makes the onboard clocks of the computers themselves obsolete, although when the machines are initially booted up, or if there has been a delay in contacting the NTP server (if it is down or there is a temporary fault), the onboard clock is used to maintain time until full synchronisation is again achievable.

Time Servers and the Internet

  |   By

Timing is becoming increasingly crucial for computer systems. It is now almost unheard of for a computer network to function without synchronisation to UTC (Coordinated Universal Time). And even single machines used in the home are now equipped with automatic synchronisation. The latest incarnation of Windows for instance, Windows 7, connects to a timing source automatically (although this application can be turned off manually by accessing the time and date preferences.)

The inclusion of these automatic synchronisation tools on the latest operating systems is an indication of how important timing information has become and when you consider the types of applications and transactions that are now conducted on the internet it is of no surprise.

Internet banking, online reservations, internet auctions and even email can be reliant on accurate time. Computers use timestamps as the only point of reference they have to identify when and if a transaction has occurred. Mistakes in timing information can cause untold errors and problems, particularly with debugging.

The internet is full of time servers with over a thousand time sources available for online synchronisation however; the accuracy and usefulness of these online sources of UTC time do vary and leaving a TCP/IP open in the firewall to allow the timing information through can leave a system vulnerable.

For network systems where timing is not only crucial but where security is also a paramount issue then the internet is not a preferred source for receiving UTC information and an external source is required.

Connecting a NTP network to an external source of UTC time is relatively straightforward if a network time server is used. These devices that are often referred to as NTP servers, use the atomic clocks onboard GPS (Global Positioning System) satellites or long wave transmissions broadcast by places such as NIST or NPL.

NTP Servers and the Different Time Sources

  |   By

NTP servers are essential devices for computer network time synchronisation. Ensuring a network coincides with UTC (Coordinated Universal Time) is vital in modern communications such as the Internet and is the primary function of the network time server (NTP server).

As their name suggests, these time servers use the protocol NTP (Network Time Protocol) to handle the synchronisation requests. NTP is already installed in many operating systems and synchronisation is possible without an NTP server by utilising an Internet time source, this can be unsecure and inaccurate for many network needs.

Network time servers receive a far more accurate and secure time signal. There are two methods of receiving the time using a time server: utilising the GPS network or receiving long wave radio transmissions.

Both these methods of receiving a time source are secure as they are external to any network firewall. They are also accurate as both sources of time are generated directly by atomic clocks rather than an Internet time service that are normally NTP devices connected to a third party atomic clock.

The GPS network provides an ideal source of time for NTP servers as the signals are available anywhere. The only downside of using the GPS network is that a view of the sky is required to lock-on to a satellite.

Radio referenced time sources are more flexible in that the long wave signal can be received indoors. They are limited in strength and not every country has a time signal although some signals such as the German DCF and the USA WVBB are available in neighbouring states.

Atomic Clocks and Gravity

  |   By

We couldn’t live our lives without them. They affect almost every aspect of our daily lives and many of the technologies that we take for granted in today’s world, just couldn’t function without them. In fact, if you are reading this article on the Internet the there is a chance you are using one right now.

Without knowing it, atomic clocks govern all of us. From the Internet; to mobile phone networks and satellite navigation, without atomic clocks none of these technologies would be possible.

Atomic clocks govern all computer networks using the protocol NTP (network time protocol) and network time servers, computer systems around the world remain in perfect synchronisation.

And they will continue to do so for several million years as atomic clocks are so accurate they can maintain time to within a second for well over 100 million years. However, atomic clocks can be made even more accurate and a French team of scientists are planning to do just that by launching an atomic clock into space.

Atomic clocks are limited to their accuracy on Earth because of the effects of he gravitational pull of the planet on time itself; as Einstein suggested time itself is warped by gravity and this warping slows down time on Earth.

However, a new type of atomic clock named PHARAO (Projet d’Horloge Atomique par Refroidissement d’Atomes en Orbit) is to be placed aboard the ISS (international space station) out of reach from the worst effects of Earth’ gravitational pull.

This new type of atomic clock will allow hyper accurate synchronization with other atomic clocks, here on Earth (which in effect will make synchronization to an NTP server even more precise).

Pharao is expected to reach accuracies of around one second each 300 million years and will allow further advances in time reliant technologies.

IEEE 1588 Time Protocol Promises More Accurate Time Synchronisation

  |   By

Despite being around for over twenty years, the current favoured time protocol by most networks, NTP (Network Time Protocol) has some competition.

Currently NTP is used to synchonise computer networks using network time servers (NTP servers). Currently NTP can synchronise a computer network to a few milliseconds.

The Precision Time Protocol (PTP) or IEEE 1588 has been developed for local systems requiring very high accuracy (to nano-second level). Currently this type of accuracy is beyond the capabilities of NTP.

PTP requires a master and slave relation ship in the network. A two-step process is required to synchronise devices using the IEEE 1588 (PTP). First, determination of which device is the master is required then the offsets and natural network delays are measured. PTP uses the Best Master Clock algorithm (BMC) to establish which clock on the network is the most accurate and it becomes the master whilst all other clocks become slaves and synchronise to this master.

IEEE (Institute of Electrical and Electronic Engineers) describes IEEE 1588 or (PTP) as designed to “fill a niche not well served by either of the two dominant protocols, NTP and GPS.  IEEE 1588 is designed for local systems requiring very high accuracies beyond those attainable using NTP. It is also designed for applications that cannot bear the cost of a GPS receiver at each node, or for which GPS signals are inaccessible.” (quoted in Wikipedia)

PTP can provide accuracy to a few nano-seconds but this type of accuracy is not required by most network users however, the target use of PTP appears to be mobile broadband and other mobile technologies as PTP supports time-of-day information, used by billing and service level agreement reporting functions in mobile networks.